As the saying goes, “a thousand miles of embankment, collapsed in an ant colony”, for the decoration of such a large project involves many aspects and many details, the quality of the details of the Department of the quality of the direct impact on the quality of the entire house decoration. Many times, an unattractive decoration detail is not done well, it is likely to bring trouble to the home life in the future or even security risks. Therefore, in the decoration, any details can not be sloppy, missing.

Problem 1: Floor seams are too large and cracking

Supervisor explanation: According to 2.8.8 of the local standard DBJ/T01-43-2003 of Beijing Municipality, the flatness of wooden floor covering shall be less than 1.5 mm within 5 meters and the width of the gap shall be less than 0.5 mm. In composite floor paving, the most important thing is that the first row should be straight spliced, and it must be tight, otherwise the more difficult it is, the more difficult the paving will be, resulting in tighter gaps.

Question 2: There is no "S" bend supervision for basin water: In the course of renovation, if the sanitary ware and pipe installation of the bathroom are not standardized, it will cause inconvenience for future use. In order to reduce costs, merchants often use plastic water pipes. They do not make "S" bends during installation, which can lead to odors in the entire bathroom. It is recommended to use stainless steel pipes with "S" bends.

Question 3: The installation of cabinets is not standardized. Supervision explains: When installing the basin in the cabinet, check whether the basin material, brand and accessories are complete. No special circumstances are allowed and no accessories should be saved. When testing and acceptance of the water, store the water and then unscrew the water outlet. Observe each connection carefully. In this case, some of the accessories are omitted and replaced with other accessories.

Question 4: The supervision of outlets lacking earth line explains: According to the provisions of 16.3.9 of the national standard GB50327-2001 electrical installation, when facing the outlet when installing the power outlet, the neutral line (N) should be on the left and the phase line (L) on the right. Upper grounding wire (PE). The red light in the middle of the three-phase detector in the figure lights up, which means that there is a lack of ground. The lack of ground wires will shorten the life of appliances such as refrigerators and water heaters.

Question 5: Excessive water content of wood keel supervision explanation: According to Beijing Municipal Standard DBJ/T01-43-2003 8.2.1, wood flooring should be damp-proof before wood flooring, and the wood keel used must be baked. Dry, moisture content less than 12%. In addition, wood keels should be protected against decay and corrosion. In addition, the spacing of wooden keel nails should be less than 60 cm.

Question 6: Luminaire installation without expansion screws Supervision explained: According to the provisions of GB 16.3.10 of JB50327-2001, when the weight of the luminaire exceeds 3 kg, the embedded parts shall be installed on the top plate first, and then the lamps shall be fixed at the rear Embedded on the piece. In the picture, this phenomenon is that the luminaire is directly fixed on the suspended ceiling. An angle or steel bar should be led from the original roof first, and then the luminaire should be connected with it.

Entrance decoration Children's room Decoration Sockets Electrical appliances Home decoration pictures Home decoration Stainless steel cabinets Bathroom ceiling materials Bathroom ceiling Bathroom pictures Home decoration Home decoration

Stainless Steel Sliding Door

Characteristics and Advantages

(1) Intelligent control design: adjustable main parameter and secondary parameter automatically according to the weight of door leaves;

(2) Low noise: Special static sound track, integration of motor, worm-gear and retarder.

(3) Anti-clamping function: automatically reverse when meeting barriers;

(4) Unique electronic motor lock: the motor will lock up when the door is forced to open.(controlled by remote or switch)

(5) Tighten force: seal door when closed, power consumption approximately 10W under standby;

(6) Advanced brushless motor(36V,100W) can automatically adopt different heavy door leaves;

(7) Bi-doors inter-locking: one of the door leaves always remains closing;

(8)Safety sensor terminal: sensor stops working when door closed;

(9)Unique coating technology: never rusty;

(10)Easy and convenient to install;

(11)Working Process: when the door leaf closes to the right place, the door leaf will slightly shift to the door frame and the ground. The rubbers on the four sides of the door leaf will completely combine with door frame and ground, which ensures air tightness. When the door is open, the rubbers will separate from door frame and ground, which avoids contraction on the ground.

Technical Specification

Technical Details:

(1) Rubber lining sealing technology combined with V groove on the guide rail enables the door completely sealed when the door closed;

(2)Special door body location technology. Semicircular surface beam on the ground matches with the V style groove at the bottom of door leaf, which stop the door from swing and make sure it moves stable and smooth;

(3) The door body decorated with matte stainless steel or spray surface, and on the middle and both sides with sealing stripes to ensure the hermetic effect.

(4)Feet sensor switch applied to avoid contagion;

Stainless Steel Sliding Door,Stainless Steel Bypass Sliding Door,Stainless Steel Interior Sliding Door,Stainless Steel Folding Sliding Door

Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hffreezerdoor.com