FRP activated carbon adsorption tower structure FRP activated carbon adsorption tower structure Acid gas absorption tower is a circular overlapping segmented assembly structure. The flame retardant unsaturated polyester is used as the matrix, and the wax-free and flawless glass fiber cloth is used as the main reinforcing material, and is produced through several production processes. The exterior is made of anti-aging flame retardant polyester resin. Its advantages: FRP is not limited by the family, summer climate change, beautiful, durable, corrosion-resistant. The FRP acid gas absorption tower is divided into upper tower body, cylinder body and circulating liquid waste. The tower has two layers of packing, one layer of corrugated plate and two layer step ring, which have large surface area gas-liquid contact and full mass transfer. efficient.
Commercially pure or low-alloy nickel may contain very small amounts of alloying elements to absolutely none. By contrast nickel alloys contain significant amounts of added elements. Nickel and nickel alloys are both non-ferrous metals that are useful in a range of applications, most of which involve corrosion resistance and/or heat resistance.
Nickel Alloy alternatives to trademark [brand" names.
Alloy C276 alternative to Hastelloy C-276 and Hastelloy C
The models currently produced by our factory are available in 1.5 types, 3 types, 5 types, 7.5 types, 10 types, 20 types, 30 types, 40 types and 50 types. The BJS type acid gas purification tower is made of glass fiber reinforced plastic and polyvinyl chloride material. The outer surface of the tower is made of water-resistant and aging-resistant gel coat resin as the anti-aging surface layer, and the thickness of the gel coat layer is not less than 0.5 mm. An alkali-free, wax-free and non-twisted fine-grained fine cloth is used as the aging-resistant layer between the inner and outer surfaces. The resin content is not less than 75%, and the number of layers is 60-70% according to the requirements of large-scale and technical standards. To make the tower body absolutely reliable.
installation:
1. All parts must be inspected and inspected before installation. If there is any defect or deformation, it must be repaired before installation.
2. The purification tower must be installed on the same level of concrete foundation. The anchor screws are reserved holes and installed by secondary irrigation.
3. The connection of the purification tower assembly and the spray pipe and fittings must be tight to prevent leakage.
4. After installation, the debris in the tower and the spray circulation pipeline and the filter ring must be removed to avoid clogging the filtrate and nozzle.
The FRP activated carbon adsorption tower structure equipment body is mainly made of carbon steel or stainless steel "target=_blank> stainless steel, which is internally treated with anti-corrosion treatment. It has corrosion resistance against strong acid and alkali and salt. Under long-term operation and use, it is not subject to other factors. Oxidation corrosion. The thickness of the main structure is required according to each model and processing capacity, and is sufficient to support the load required for the structure and operation, and provide the necessary operation platform.
The adsorption unit is the core component installed in the HXF exhaust gas purifier. The adsorption unit is installed in a layered drawer in the equipment cabinet, which can be easily taken out from the inspection doors on both sides. And the inspection door is easy to open and tightly sealed. The inspection door of the large HXF exhaust gas purifier is divided into upper and lower two, which can be opened separately and removed separately.
maintain:
1. The concentration of NaOH solution in the reservoir should be kept within the range of 2-6%.
2. When the concentration is less than 2%, the NaOH solution must be added.
3. Periodically change the solution when the concentration of salt formed by acid-base neutralization in the liquid storage tank is higher than 20% or the actual use.
The principle of the FRP activated carbon adsorption tower utilizes the surface force of the high-performance activated carbon adsorbent solid itself to attract the adsorbent of the organic waste gas molecule to the surface of the adsorbent, and can exhaust the organic solvent such as benzene, alcohol, ketone, ester and gasoline. Adsorption, more suitable for high air volume and low concentration of exhaust gas treatment, suitable for electronics, chemical, light industry, rubber, machinery, shipbuilding, automotive, petroleum and other industries.
The HXF series activated carbon exhaust gas purifier is a dry exhaust gas treatment device. It consists of a tank and an adsorption unit filled in the tank. According to the number of adsorption units and the air volume are divided into eight specifications, JTF series activated carbon exhaust gas purifiers can choose different fillers to handle a variety of different exhaust gases, mainly including three categories:
1. Acidic exhaust gas and acid mist (eg NO2, H2SO4, HCL, HF, etc.)
2. Alkaline exhaust gas (eg NH3, etc.)
3. Organic waste gas and odor (eg benzene, phenols, alcohols, ethers, terpenes) This article URL: http://
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Nickel And Nickel Alloys
Nickel is a versatile, highly corrosion resistant element that will alloy with most metals. Due to its corrosion resistance, nickel is used to maintain product purity in the processing of foods and synthetic fibers. It is highly resistant to various reducing chemicals and is unexcelled in resistance to caustic alkalies. In addition, nickel has good thermal, electrical and magnetostrictive properties. Relatively high thermal conductivity of this metal has lead to its frequent use for heat exchangers
Alloy B-2 alternative to Hastelloy B-2
Alloy C-22 alternative to Hastelloy C-22
Alloy X alternative to Hastelloy X and Inconel HX
Alloy 20 alternative to Carpenter 20 and Incoloy 20
Alloy718 alternative to Inconel 718
Alloy 800 alternative to Incoloy 800
Alloy 800H/HT alternative to Incoloy 800H/HT
Alloy 400 alternative to Monel 400
Alloy K-500 alternative to Monel K-500
Alloy 625 alternative to Inconel 625
Alloy 600 alternative to Inconel 600
Alloy 601 alternative to Inconel 601
Nickel Alloy Steel Tube,Seamless Nickel Alloy Steel Tube,Nickel Alloy Protection Tube
YUHONG GROUP CO.,LIMITED , https://www.jessro-pipefittings.com