Single-section stone breaking machine - single-stage crushing machine - single-stage crusher - Lida specializes in selling single-stage stone breaking machine for crushing general brittle ore, such as limestone, argillaceous siltstone, shale, gypsum and coal. It is also suitable for the crushing of limestone and clay. The single-stage stone breaking machine has the structural features of full-turning mass hammer, adjustable crushing plate, forward tweezers and safety door. It is suitable for the process requirements of large feed size, large crushing ratio and one-time grinding. At present, 5000t/d or even l0000t/d cement clinker production lines are gradually popularized, and the demand for large-scale cement production equipment has also increased. Among them, the limestone crushing capacity is over 1000 t/h, and the single-stage hammer type is adapted to the requirements of the vertical grinding process system. Stone machines have a fairly broad market demand. The main technical performance parameters of the http:// impact crusher single-stage stone breaking machine are as follows. Feeding port size: 1805mm × 2560mm; maximum feeding size: ≤ l 000mm × l 250mm × 1500mm (of which ≥ 1 m3 large block should not exceed l0%); production capacity: l 000t / h; discharge granularity: ≤ 100 Mm (more than 95%); motor power: 1000 kW; motor voltage: 10000 V; machine dimensions (excluding attachments): 4900 mm × 4100 mm × 4200 mm. Most of the 1000t/h stone breaking machines selected by major domestic cement plants are double-rotor hammer type stone breaking machines. In the domestic single-rotor stone breaking machine of the same type, only the single-machine output of the single-stage stone breaking machine can reach this order of magnitude stably. Http:// iron ore crusher Copper nuts made of all kinds of embossed wire (usually lead brass, such as H59, 3604, 3602). Our daily contact with the embedded knurled copper nuts are processed by precision automatic lathes. The reference standard of embedded knurled copper nut comes from GB/T809, but the technical parameters of all kinds of embedded nuts produced by our company exceed the relevant indexes required by the national standard.
Compared with the double-rotor stone breaking machine, the single-stage hammer type stone breaking machine has one less motor and transmission system and one less rotor. The main advantage is that the single machine cost of the stone breaking machine itself is very low, and the majority of users break the single rotor. The use of stone machines is more familiar. Http:// Counter-attack rockbreaker closely tracks the use of single-stage hammer-type stone-breaking machine, and timely corrects the shortcomings of each link. The single-stage hammer-type stone-breaking machine after shaping has become the highest output in Taiwan. The single-rotor hammer type stone breaking machine has broad market prospects.
This series of single-stage stone breaking machine introduces German advanced technology, optimized design and structural improvement, designed and manufactured a new generation of efficient stone breaking machine. After years of use and improvement, it has developed into a more mature fourth-generation product. The single-stage stone breaking machine can crush the large ore collected from the mine to an average particle size of 5mm. It is an ideal replacement product for the traditional two-stage and three-stage crushing methods, simplifying the process flow, saving infrastructure investment and production costs. The crushing ratio is large: the maximum feed particle size can reach 1.3-1.5m. The discharge particle size range of 3-150mm can be adjusted. Fine discharge: the processed aggregate has good grain shape and the powder material is ≤20%. Process simplification: the original secondary or tertiary crushing can be reduced to one section. Low operating cost: the system supporting power is small, and the production cost is greatly reduced.
The single-stage stone breaking machine material enters the crushing chamber and is stacked on the special intermediate bracket in the machine. The hammer head runs in the gap between the intermediate brackets, and the material is continuously crushed and dropped. The falling small pieces are operated at high speed. The hammerhead is further struck and shredded, and finally the arc-shaped slabs are integrated and discharged.
The main technical parameters of single-section stone breaking machine: http:// Model specification Feed particle size (mm) Discharge size (mm) Production capacity (t/h) Supporting power (kw) Theoretical weight (T) DPC-15 ≤500 ≤5mm accounted for 80% 15~35 22~45 11 DPC-35 ≤700 ≤5mm accounted for 80% 35~60 55~75 16 DPC-65 ≤800 ≤5mm accounted for 80% 60~90 90~132 19 DPC-90 ≤900 ≤5mm accounted for 80% 90~125 132~200 twenty three DPC-125 ≤1100 ≤6mm accounted for 80% 125~180 200~280 28 DPC-180 180~250 280~380 33 DPC-250 ≤1300 ≤6mm accounted for 80% 250~400 450~630 43 DPC-300 450~650 630~800 55
Http://news.chinawj.com.cn 
Submission:
Knurling copper nut is mainly used for hardware Spring, shaped spring, craft gift spring, battery spring, spring antenna,key ring, phosphorus copper spring CNC automatic lathe turning parts (copper car parts, iron, aluminum car parts), metal stamping parts, electronic parts, iron shaft, single Rachel,Rachel, iron pin, non-standard Screw nut,fittings,fasteners, wire forming (wire card holder, Model aircraft landing gear, S hook, R latch, triangle buckle, D buckle) and other hardware products, belonging to the copper nut series.
Brass Nut,insert nut,knurled nut,injection nut,hex nut
Shenzhen Lanejoy Technology Co.,LTD , https://www.szlanejoy.com