Many people use wallpaper as a decoration element in order to decorate a stylish bathroom. However, there are five principles that need to be mastered in wallpaper paste, but the effect and use will be affected. 1. When the base layer is treated to treat the surface of the base layer, the base layer must be cleaned so that it is free from dust, oil stains, and debris. 2. Before the line is pasted on the wallpaper, first the line must be played. The line is to play horizontal and vertical lines on the processed grass, so that the paste has a basis and the quality of the paste is guaranteed. 3, paper cutting paper is an important part of wallpaper paste, should be measured in the height of the top of the wall to the bottom, the paper will be cut in the ground, wallpaper blanking size should be 10-20 mm longer than the actual size, cut a good After the wallpaper has been wetted, it can be affixed. Generally, after the water is soaked in the water, it can be brushed for 10 minutes. 4, brush glue brush glue is the key link of wallpaper paste, in order to ensure the firmness of the paste, the back of the wallpaper and the wall surface should brush glue, require the glue to brush evenly, tightly, can not miss the brush, be careful not to wrap, from the heap , from the heap, to prevent dirty wallpaper. The width of the wall should be 30mm wider than the width of the wallpaper. 5, paste the wallpaper wallpaper principle is the first vertical level, the first after the next, the first high after the low. Summer decoration knowledge floor purchase entrance decoration wallpaper
SRD Top Sellers include: Butyl Tapes; EPDM Waterproofing membrane; TPO; PVC; Roof Sealant; Roofing Plates and Screws.
EPDM: could be used on roof, RV. It is suitable for low slope, roofing applications, new and re-roof.
Butyl Tapes: it is suitable for both commercial and residential uses. It is an ideal product to fix the leak in gravity tanks; roofs; drainpipes and pans; trail sealings. It is sturdy, heavy-duty, and has great weather resistance. One roll of Aluminum Butyl Tape could fix your leaking headache.
TPO Waterproofing Membrane: It is an advanced-formula, heat-weldable Waterproofing Membrane Specification TPO or thermoplastic polyolefin is a single-ply reflective Roofing Membrane. It is composed of polypropylene and ethylene-propylene rubber which are polymerized together to form what we call TPO. This synthetic roofing membrane comes in various thickness and dimensions.
PVC Waterproofing Membrane: It is an advanced-formula, heat-weldable PVC thermoplastic membrane that is designed for long-term weather-ability and performance. The physical properties of the membrane are enhanced by a tenacious, weft-inserted polyester fabric that is encapsulated by thick PVC- based top and bottom plies. The smooth surface of the PVC membrane allows for a total-surface fusion and permanent weld, creating a consistent, watertight, monolithic roof assembly. PVC can be used in adhered and mechanically fastened systems.
One-component Exposed Polyurethane Sealant is a solvent-free one-component sealant.The sealant is in paste form and can be squeezed out or applied by spread.Sealant is a material used to fill voids (holes, joints, seams, etc.) and has both the functions of bonding and sealing.Adhesive to metal, rubber, wood, cement components, ceramics, glass, etc.The cured rubber layer is rubbery and elastic.
TPO Membrane Weld Plates are available for use with TPO membranes. Suitable for rigid substrates such as gypsum board, cement board, etc., then induction welded with thin films to form non-vertical connections to resist wind loads. Plate diameter: 80mm;Hole diameter: 6.8mm. Color: Front side: Light green;Back side: Epoxy light brown/light grey/Or anti-finger print alu-zinc film. FM approved.
PVC Membrane Weld Plates are available for use with PVC membranes. Suitable for rigid substrates such as gypsum board, cement board, etc., then induction welded with thin films to form non-vertical connections to resist wind loads. Plate diameter: 80mm; Hole diameter: 6.8mm. Color: Front side: pink/purple; Back side: Epoxy light brown/light grey/Or anti-finger print alu-zinc film. FM approved.
Galvalume Steel Round Barbed Plates are made of aluminum plus galvanized steel. The plate's rounded design and stiffening ribs provide excellent strength against the lifting forces of the wind. SRD (60 mm) seam plates are used for lap seam fastening. SRD (73 mm) insulating plates are used to fasten the insulation. These panels are designed to be insulated for use with fasteners in TPO/PVC roofing systems with ply-Iso. FM approved.
Galvanized Steel Roofing Screws are specially designed to be : used for the attachment of TPO thermoplastic membranes to approved substrates. Screws and plates will be used with TPO heavy duty or general purpose fasteners for 22 gauge steel, wood, or structural concrete decks. They can also be used with SRD Roof Fasteners to attach membranes to structural steel purlins. Material:Hardened Carbon Steel. Thread Diameter: 6.3mm. The regular length can be 32mm-280mm (1 1/4"-11") or customized. FM approved. WaterproofingTop Sellers,Waterproofing Membrane,Epdm Waterproofing Membrane,Waterproof Membrane,Roof Sealant Suzhou Smart Building New Materials Co., Ltd. , https://www.srdwaterproofing.com
Anwar bathroom 