Many families choose to tile the walls and floors when decorating the bathroom. In the bathroom building, choose your favorite tiles, the next step is to choose different tiles. The following small series for everyone to introduce the bathroom tile laying process specification and other related knowledge. First, bathroom tile stickers note: 1, to avoid the tile water absorption rate is too large When buying tiles, it is important to check the water absorption of the tiles. Drop water droplets on the back of the tile to see how fast the water spreads after it has spread. In general, the slower the absorption of water, the greater the density of the tile, and the smaller the water absorption density, so that the tiles that are laid out can remain undistorted and look natural and beautiful. 2, avoid the tiles on the back of the line is too shallow In order to fit the tile closely to the wall, the back is generally designed with lines. When the lines are relatively deep, it can be ensured that the tile and the cement mortar layer will not fall off when they are partially detached, and if the texture is too shallow, the falling of the tile will inevitably occur. 3, sand is best to choose sand When paving bathroom tiles, in addition to selecting the main material - ceramic tile, you must choose accessories - sand, the thicker the sand, the higher the strength of the formulated cement mortar, but if the intensity is too high, it will lead to some bad The results, such as the use of the leveling of the ground will appear cracking, so nine positive home network recommends that you choose the best sand. 4, the base layer of paving tiles need to be handled well To avoid emptying the tiles, first the tiled wall and floor base must be clean. Be sure to remove all types of dirt on the wall and wet the ground with water one day in advance to control the humidity to 30-70%. Only after the grassroots work is done can the quality of follow-up work be ensured. 5, cement mortar needs to be full and even When applying a good cement mortar to the back of the tile with a spatula, it is necessary to pay attention to the fullness and evenness of the cement mortar. 6, reserve enough expansion joints This is an important detail to pay attention to in the bathroom tile laying process. 2-5mm expansion joints should be reserved for tile laying. If there are not enough expansion joints, under the effect of thermal shock expansion or moisture expansion, stress may occur between adjacent tiles and squeeze, resulting in empty drum fall off. Second, bathroom tile color choice: 1, the color should not be too miscellaneous, so as not to "add to chaos" The color of the bathroom tile needs to be matched with the color of the three large parts of the bathroom so as to show a good overall effect. Generally speaking, the color choices of the three large parts of sanitary ware are the same, and the color in a room should not be more than three, otherwise it is easy to make people feel dazzling. 2, bathroom tile color and overall color complement each other If the color of the three major parts of the sanitary ware is dark, the color of the tiles can be selected with light color or the same kind of color; if the three major parts of the sanitary ware are light-colored cold colors, then the color of the tile is best to choose dark or light-colored warm Color to match. 3, white classic, never ending At any time, white will make the main color in any place. The use of white tiles for bathroom decoration will never be outdated, meeting the aesthetic requirements of any crowd. White tiles give people a clean, hygienic and bright feeling. These are the standards that all bathrooms have been pursuing. 4, the size of the area is not the same, there are differences in color choice Because the area of ​​the bathroom is generally relatively small, it is easy to give people the feeling of depression, so when choosing the bathroom tiles, you should try to choose the bright colors of the tiles, white and milk yellow are generally better choices, and gray, blue, Red and other shades of tiles should be avoided as much as possible. Because the dark tiles make people feel the space becomes smaller, the more the room becomes dark and narrow. Third, bathroom tile laying process specification Bath tile pre-layout process specification 1. Bathroom tile specifications and area coordination Bathroom tile specifications should not be too large, the overall size is too large to feel uncoordinated, and at the same time not easy to install floor drain. General kitchen tiles are mostly 300*300 or 330*330. 2 before the bathroom tile laying tile plan Paving bricks before making a plan, try not to appear less than one-third of the narrow columns. It must be processed and cut, and it is advisable that after the tile is cut, it should be greater than two-thirds. 3. Confirm the tiles used before paving Before the bathroom tile is tiled, confirm the tiles used in the bathroom wall everywhere to prevent confusion of the bathroom tiles, so as to avoid the phenomenon of misuse of tiles. 4 waterproof bathroom tiles before treatment The tiled front wall of the bathroom needs to be treated with waterproofing. If you use the method of sticking the tiles first and then put them on the tile, you need to make a water-retaining test before paving the tiles. It is best to make the floor waterproof again. 5. Understand the trend of hydropower wiring Before laying, it is necessary to remember the line direction of the wall ground water pipe wires. It is better to keep the circuit and water route maps, so that it can be easily searched for in the future. Specification of bathroom tiles in the process specification 1. Ratio of cement mortar paving bathroom tiles The cement used for cementing the bathroom tiles is No. 425 cement. The mixing ratio of cement sand shall not be greater than 1:3. If the cement content is too heavy, the expansion coefficient of the cement will cause the cracking of the tiles and reduce the service life of the tiles. 2. Length of bathroom tiles soaked in water If glazed wall tiles are used in the bathroom and cement mortar is used as the adhesive, the tiles need to be soaked with water, and the time for soaking the water is appropriate after the tiles are completely soaked. The time is usually 30 minutes. . 3. Paving to leave seams Paving bathroom tiles, whether belonging to a seamless brick, must be left seam, it is recommended not less than 1mm, ordinary wall tiles to 1.5-2mm is appropriate, antique brick gap can be appropriately widened. 4 bathroom wall tile height The paving height of the bathroom wall tiles is higher than the height of the ceiling, generally not less than 10 cm. 5. Tile texture alignment Pay attention to the texture of the tile when paving the tile, do it along the texture paving, the front and back of the tile line should pay attention to its direction, do not paste down, the texture of the tile waist line and the brick texture consistent. After the bathroom tile laying process specification 1 bathroom tile joint interval length Stitching should be done after the tiles are dried. It is usually carried out after 24 hours. 2. After walking to dry on the ground After the floor tiles are tiled, they must wait for the floor to dry before walking around the tiles or other kitchen and bathroom renovation projects. 3. After the bathroom tile inspection After the tiles are laid, it is necessary to check them. If it is found that there is an empty drum, it is better to patch and refill the defective areas. 4 bathroom tile wall punching strength The wall punching needs attention, and it is best to spray water at the hole where the hole is punched for cooling treatment to prevent the tile from bursting due to the local temperature change of the tiles in a short time. 5. Empty wall inspection When drilling a hole in the wall, be sure to check if there is any empty drum. Also, check the pipeline diagram of the hydropower reform that has been saved and do not hit the pipeline. The above is related to the introduction of the process specifications for toilet tiles, etc. If you want to know more relevant information, please pay more attention to this website and provide you with more complete, more detailed and updated information. How to decorate the bathroom bathroom decoration toilet decoration bathroom storage decoration design simple bathroom dry area decoration design
Ningbo Actmix produce the Pre-Dispersed Rubber Chemicals With NBR As Binder,NBR-bound Rubber Chemicals,application for the NBR parts.
Has exceleent dispersibility, high uniformity, high stably. Suitable for automobile production line.
Our chemicals included DPTT-75GN, ETU-75GN, S-80GN, TMT-80GN, ZDMC-80GN, ZnO-80GN.
Basic acclererator for sulfur-cured rubber, especially for application made of NBR rubber.
Pre-Dispersed Rubber Chemicals With NBR As Binder Pre-Dispersed Rubber Chemicals With NBR As Binder, Basic Accelerator For Sulfur-cured NBR Rubber Ningbo Actmix Rubber Chemicals Co.,Ltd. (Ningbo Actmix Polymer Co.,Ltd.) , http://www.actmix-chemicals.com
